Skip to content

Usage Guide

Shortcut or Instance?

There are two ways to use HttpCommand.

  • Use one of its shortcut methods (Get, Do, GetJSON) to execute a single HTTP request and examine the response from the host. When you use a shortcut method, HttpCommand will create a new, local, instance of itself and then use the instance's Run method to send the request and receive the response, then exit thereby destroying the local instance. This is generally fine when your requests are independent of one another and do not require any state to be maintained across requests.
  • Create an instance of HttpCommand using ⎕NEW or the New shared method, set whatever parameters are necessary, execute the Run method, and examine the response from the host. Creating an instance of HttpCommand and using the Run method to send the request and receive the response will persist the instance such that state information like connection information and HTTP cookies will be retained across requests.

HttpCommand's Result

The result of the Run method is a namespace containing information related to the result of the request. The display format (⎕DF) of the result presents some useful information.

      ⊢r ← HttpCommand.Get 'https://www.dyalog.com'
[rc: 0 | msg:  | HTTP Status: 200 "OK" | ⍴Data: 20571]
  • r is the namespace result
  • r.rc is HttpCommand's numeric return code. 0 means HttpCommand was able to create and send the request to the host, send it, and receive and process the response.
    If rc is less than 0, it means there was some problem either composing/sending the request or processing the response.
    If rc is greater than 0, it is the Conga return code and generally means that Conga encountered something unexpected. More information about rc can be found here.
  • r.msg is a (hopefully meaningful) message describing whatever the issue was if r.rc is non-zero.
  • r.HttpStatus is the numeric HTTP status code returned by the host. A status code in the range 200-299 indicates a successful HTTP response with 200 being the most common code.
  • r.HttpMessage is the HTTP status message returned by the host.
  • r.Data is the payload of the response, if any, returned by the host. The result namespace contains other elements which are described in detail on the Request Results, Operational Results, and Response Results pages.

Typical Use in Code

Typical use of HttpCommand might follow this pattern.

 resp ← HttpCommand.Get 'some-url'
:If resp.IsOK ⍝ use the IsOK function from the result namespace
    ⍝ code to process the response 
:Else
    ⍝ code to handle bad request
:EndIf

If you expect to make several HttpCommand calls, you may want to create an instance and then update the necessary settings and execute the Run method for each call. This can be useful when the requests are made to the same host as the connection to the host will be kept open, unless the host itself closes it.

 hc←HttpCommand.New 'get'  ⍝ here we expect all requests to be HTTP GET
 urls←'url1' 'url2' 'url3'

:For url :In urls ⍝ loop over the URLs
  hc.URL←url ⍝ set this URL
  resp←hc.Run
  :If resp.IsOK
    ⍝ process the response
  :Else
    ⍝ process the exception/error
  :EndIf
:EndFor 

Timeout and Long-running Requests

The default Timeout setting (10 seconds) is adequate for most requests. There are a couple of patterns of long running requests. Timeout can be set to a positive or negative number.

  • Setting Timeout to a positive number means that HttpCommand will time out after Timeout seconds with a return code (rc) of 100. Any partial payload received will returned in Data element of the result.
  • Setting Timeout to a negative number means that HttpCommand will not time out as long as data is being received. This is useful in the case where a large payload may be received but you are uncertain of how long it will take to receive. If no data is received within a period of |Timeout seconds, HttpCommand will time out with a return code (rc) of 100. Any partial payload received will be returned in the Data element of the result.

    Using a negative Timeout value is useful in the case where a large payload is being received in chunks but has no benefit if the entire payload is sent in one chunk or if the host takes more than |Timeout seconds to begin sending its response. In that case, you'll need to set |Timeout to a larger value.

Compressing Response Payload

HttpCommand can accept and process response payloads that are compressed using either the gzip or deflate compression schemes. To accomplish this, you need to set the accept-encoding header to 'gzip, deflate'.